Monday, August 17, 2020
Running around, Finally!
It has taken a couple of weeks but I now have the east end of the Sugarwood Siding connected.
That in itself does not allow me to preform run a around because, the west turnout of Sugarwood Siding is at the end of the curve coming from the west. So that curve had to be laid and is complete now.
Spline roadbed laid and laying the ties.
Rails down.
With the exception of the spurs for McFoods and Olie’s Cold Storage the Sugarwood Yard section is complete.
As can be seen in the pictures above I have started working on McFoods and I have mocked up the wall panels.
I don’t think I will be installing the McFood and Olie’s Cold Storage spurs until I have the structures figured out. For now, the next step is run trains and push/pulls cars and get the track reliable. My Genset and MP15AC (B type trucks - 2 axles) have no issues with any portion of the track work so far but my SD40-2 (C type trucks - 3 axles) has an issue with the diverging route of the turnout at the east end of Surgarwood Siding.
I also want to get the other three modules of the layout built and install before the end of September.
Until next time.
For information about me check out the About page on this blog.
Tuesday, August 4, 2020
I’m about to run around!
Over the past week and holiday, I was able to complete laying the track for the Sugarwood Yard and I started laying the sub-roadbed to complete the east end of Sugarwood Siding.
There is not a whole lot to be said about laying the track in the yard it is pretty straight forward. Thought I did want the yard to look like it has been around for a while so I did not use a straight edge to lay the yard perfectly straight, as can be seen in the two photos below.
To connect the east end of Sugarwood Siding I decided to go with the spline roadbed approach and I find it easier and faster than I thought. I am using 1/8” x 1/8” basswood glued to the foam. I have been surprised that how fast the glue dries, about thirty minutes after laying a spline I can remove the pins and lay another spline. Towards the upper center of the top photo and left center of the bottom photo, the east end of Sugarwood siding can be seen.
Until next week.
For information about me check out the About page on this blog.
Monday, July 27, 2020
A Slow Week
Work on the layout proceeded a bit slower this week.
I having been working on Sugarwood Siding and had to build the two industry turnouts for McFoods and Olie’s Cold Storage. These two turnouts are now installed and connected to the west end of Sugarwood Siding.
I am stilling deciding on just how to connect the east end of the siding and the industry tracks.
My current thinking is to use 1/8-inch x 1/8-inch strips and take the spline roadbed approach. Another approach I am considering is to create a template and cut it out of a plank of basswood.
The benefit of the plank and template is that most of the work could be done at my workbench, the reason I am using 1/8-inch basswood/plywood for my roadbed, but I think there would be a lot of waste using the plank and template. I will have to think a bit more.
In the meantime, maybe I will work on the yard tracks.
Until next week.
For information about me check out the About page on this blog.
Sunday, July 19, 2020
A Set Back and Trains Roll
Sorry I didn’t get a blog posted last week.
The events of the week before, a lose neutral on the electric company side of the meter to our house, caused a lot of stress. We lost several surge protector power bars, a transformer on the furnace and a transformer to our alarm system. With the resolution of the power issue, life returned to the new normal and with the stress relieved my diverticulitis acted up and as a result I spent Friday before last and that weekend with a fever and pain in my gut. Not to worry, my wife insisted that I get tested for COVID and as expected the test came back negative.
That week, I did manage to install all five turnouts frog switches and their point pulls. I chose to go with crank type throw. This allowed me to have all the turnouts aligned to the straight route with the nobs pushed in and the diverging route when the nobs are pulled out.
Here are the parts that make up the switch and pulls. The green parts are 3D printed by a friend of mine.
This is a DPDT slide switch that flush mounts. Another friend of mine directed me too.
The assembled switch.
Under the layout the assembly looks like this.
A crank and sleeve ready to be installed. Once the sleeve is installed the crank in installed then bent and connected to the slide switch.
Installing the sleeve. A drop of Superglue as the sleeve is pushed in to hold the sleeve in place.
Installed Top
And Bottom all wired and installed.
So that was the end of last week.
This past week I completed the main line and installed east Sugarwood Siding turnout.
Trains Roll
Next step is to complete Sugarwood Siding and added Olie’s Cold Storage and McFoods sidings, then finish the yard track and on to scenery.
Until next week.
For information about me check out the About page on this blog.
Sunday, July 5, 2020
It Runs!
This week has been full of interesting things.
From power issues in the house to actually getting trains running, oh yea, there was Canada Day On July 1st.
I have the turnout to the Service/RIP track in and functioning as it should. I am now working on the yard ladder. Then the entrance to the yard then the sidings west turnout. With those working in can turn my attention to building the two turnouts for McFoods and Olie’s Cold Storage and then laying the rest of the track for this area.
Here are a few pictures, I hope to have a video and an explanation of installing the turnouts next week.
Join the Service/RIP turnout to the yard ladder
Facia Control Nob
Slide switch that routes power to the frog
The trowbar
Until next week.
For information about me check out the About page on this blog.